I spoke to Lippert and they told me that the LED Fabric Light Kit # LC674283 has a waterproof rating of IP55 but they don't have a Lumens rating for it. The best they could offer was the CCT which is 6000K.
I attached a picture that shows how well it illuminates under an awning though. view full answer...
The Reese Steadi-Flex Weight Distribution System # RP66560 will work for your 2019 Cruiser RV Stryker travel trailer toy hauler as long as you do not exceed 12,000lbs maximum trailer weight of the hitch. My concern is the 600-1,200lb tongue weight capacity. The 1080lbs of tongue weight is without the additional propane, batteries and any gear on the camper. You will likely exceed that with additional gear.
I do prefer the Equal-i-zer Weight Distribution System # EQ37140ET with your Stryker... view full answer...
We've got 2 different axle lift kits that you can use on your Grand Design, and it really just depends on how much of a lift you're wanting and how your axles are currently configured.
The Dexter Trailer Springs Over-Under Conversion Kit # K71-385-00 is a simple installation and the more cost-effective option but it requires that your axles are currently sitting on top of your leaf springs. This will raise your trailer the eight of your leaf spring stack plus the 3" diameter of your axles.
The... view full answer...
The AWM970 has a cutout recommendation of 9.3 inches by 6.11 inches. The Jensen RV Stereo - Double DIN - AUX/USB, Bluetooth, jControl - 12V # JWM60A will be a great fit, so that is my recommendation for your replacement. You will want to note the overall face is larger at 10-7/16 x 7 inches. This part number is technically the JWM62A you referenced which replaced the JWM60A but we kept our part number the same. view full answer...
The Hollywood Racks Sport Rider SE2 Platform Bike Rack w/ Cargo Carrier # HR1450Z-85 that you referenced can be used in the trailer hitch of your truck but it's not rated for use at the rear of a camper like your Fun Finder as the ride quality there will be much rougher.
The closest bike rack solution we have then is the reinforced Swagman Dispatch part # S44FR which you'd use at the rear of the camper and then the A-frame platform # CC-255 would be a great choice to carry cargo above... view full answer...
The etrailer # e68ZR is only available with the coupler lock in the silver finish, but you can get the locks separately as # e98895, # e98880 and # e98883 and choose the 'keyed alike' option. This would provide you with the same kit, but with a yellow slip-on coupler lock. view full answer...
The RV/Camper hitches we currently have available, like the Curt Adjustable Trailer Hitch Receiver # C13701, will have a maximum tongue weight of 500 pounds. This will fit frames anywhere from 18" wide all the way up to 51" wide, so it is versatile. However, with your motorcycle weighing 600 pounds, and the rack for it adding even more weight, we will not have an option available to accommodate this kind of weight, unfortunately. view full answer...
Because you want stability and have some knee issues, I recommend something like the Torklift GlowStep Revolution Scissor Steps w/Landing Gear-4 Steps, Item # TLA78004.
The Torklift, Item # TLA78004, has aluminum steps that are lightweight, fold up for storage, and are 8 inches deep x 22 inches wide. You can fine tune the height and level of stairs with the built-in landing gear legs which also make these steps more stable. The mounting base dimensions are 27-7/16 inches x 12 inches... view full answer...
We have the multi fit Curt hitch part # 13703 which is a Class III hitch that can be used at the rear of a travel trailer like your 2020 Cruser MPG 2550 to carry an RV approved bike rack like the Swagman XP part # S64940. view full answer...
The Go Power Automatic Transfer Switch # 34270278 that you are interested in was designed to automatically switch power sources between an inverter or an AC power source. You'd want to run the inverter you have now to this as well as the power source wiring from shore power and this would automatically take care of your AC power needs/switching. Basically your battery would connect to the inverter, the inverter to the # 34270278 and then the # 34270278 to your fuse panel. This does not... view full answer...
You should be able to install the Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" - 72" Wide # 13703 on your 2019 Shadow Cruiser travel trailer. We haven't test fit this so I can't guarantee this will fit but if you have room for a trailer hitch and your trailer frame is within the 22" - 72" width range of this product then this is the trailer hitch that I recommend. This hitch can be a bolt-on or a weld-on installation.
I have attached the installation instructions for you to... view full answer...
The hyper flashing issue you are referring to is not typically found on trailers and is more of a vehicle issue. Since the power sent to the trailer gets its signal from the vehicle the trailers lights like the # CE86FR are going to flash at the same rate as the vehicles lights flash. This happens on the trailer regardless if they are LED or Incandescent. An issue some newer vehicles have is they sense the LED lights as a bulb out issue. These would require a Adapter # 20142 if you have... view full answer...
Sounds like you are looking for the mount for the small ball of your friction sway control unit. You have a couple options like the part # D320 which is a ball mount that has the mounting tab attached to the side of the ball mount platform. We have the # 3442 which allows you to weld a tab onto your current ball mount, or we have the # RP26003 which fits between the ball mount platform and the hitch ball. view full answer...
Unfortunately there is no way to swap out the basic fans that come in your 2019 Cruiser RV Shadow Cruiser 193 MBS for a thermostatic controlled fan. You will need to replace the entire assembly which will entail removing the caulking and screws on the roof.
I recommend the MaxxFan Deluxe Roof Vent # MA00-07000K as it is one of the only fans that will allow you to operate it during rain as well. It features a 10 speed fan that can run in either direction allowing you to ventilate your... view full answer...
The Valterra Mini Rope Light you're referring too has been discontinued but yes you could cut it and splice it to a 12V power supply.
If you're just trying to add an LED light strip to replace your current LED lights, then I recommend just going with the LED Light Strip # DG52683.
This light strip is 16' long but can be cut every 3 LEDs, blue in color, and has an exposed end for you to be able to easily splice into your setup. view full answer...
The 2-5/16" Gooseneck Coupler Head # 291300 that you referenced is a gooseneck hitch coupler. It could be used with a tripod stabilizer if you had one but it's main function is for connecting a gooseneck trailer to a gooseneck ball in the bed of a truck. view full answer...
I contacted the Vender, they stated that it appears the operator mechanism on your MaxxFan Deluxe Roof Vent, # MA00-07500K is bad and needs to be replaced. Use the Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents, # MA10-20281K-1AF. view full answer...
Yes, we carry the Valterra Deadbolt Lock for RVs # L32CS3108, which will give you a standard deadbolt lock like you would see in a house. This lock fits 1-3/8" to 1-3/4" thick RV doors.
If you're just looking for a entry door lock that comes with a deadbolt, like part # 295-000019, then I would first need to know the dimensions of your trailer's cutout hole. To get this you'll need to remove the current door lock and measure the hole's height and width. Once we have that number I can... view full answer...
The Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System part # LC672136 uses the jack for the initial leveling but when all four of the pods are deployed and leveled the jack will retract.
It is perfectly acceptable to use the jacks switch to redeploy it and use it as a fifth point of contact. From my experience there wouldn't be a need for any additional support from the jack as the system is very solid but you will have the option. view full answer...
Hey Dan, so Furrion doesn't offer just the module you are looking for so only option would be a front panel like the part # FR83RV. view full answer...